Pella Door 80JJ0103 User Manual

©2008 Pella Corporation  
Part Number: 80JJ0103  
INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION  
FOR CLAD HINGED PATIO DOOR WITH ADJUSTABLE HINGES  
PARA LA PUERTA PARA PATIO REVESTIDA, CON BISAGRAS ADJUSTABLES  
%PPSꢀ5PQ  
'JO  
$PSOFS  
$PSOFS  
'MBTIJOH  
5BQF  
/BJMJOHꢀ'JO  
5PQ  
'MBTIJOH  
5BQF  
$PSOFS  
8BUFS  
3FTJTUJWFꢀ  
#BSSJFS  
'MBTIJOH  
5BQF  
4JEF  
'MBTIJOH  
5BQF  
4IFBUIJOH  
'SBNJOH  
0QUJPOBMꢀ  
/BJMJOHꢀ'JO  
4JEF  
'MBTIJOH  
5BQF  
4JMMꢀ'MBTIJOHꢀ5BQFꢀꢁꢃ  
4JMMꢀ4VQQPSU  
4JMMꢀ'MBTIJOHꢀ5BQFꢀꢁꢂ  
%PPSꢀ#PUUPN  
Always read the Pella® Limited Warranty before purchasing or installing Pella products. By  
installing this product, you are acknowledging that this Limited Warranty is part of the terms of the  
sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella  
product warranty. See Limited Warranty for complete details at http://warranty.pella.com.  
These instructions were developed and tested for use with typical wood frame wall construction in  
a wall system designed to manage water. These instructions are not to be used with any other  
construction method. Installation instructions for use with other construction methods, multiple  
units or bow and bay windows, may be obtained from Pella Corporation or a local Pella retailer,  
or by visiting http://www.pella.com. Building designs, construction methods, building materials,  
and site conditions unique to your project may require an installation method different from  
these instructions and additional care. Determining the appropriate installation method is the  
responsibility of you, your architect, or construction professional.  
 
E. Apply sill flashing tape #1. Cut a piece of flashing tape 12"  
longer than the opening width. Apply at the bottom of the  
OPENING AS SHOWN ꢁꢂ% SO IT OVERHANGS ꢂꢅ TO THE EXTERIORꢇ  
ꢃꢇ  
ꢆꢇ  
£ꢃ  
Note: The tape is cut 12" longer than the width so that it will  
extend 6" up each side of the opening.  
ꢃꢋꢂꢇ  
ꢃꢋꢂꢇ  
F. Tab the sill flashing tape and fold. Cut 1" wide tabs at each  
CORNER ꢁꢂꢀꢃꢅ FROM EACH SIDE OF CORNER ꢁꢂ& ꢇ &OLD TAPE TO THE  
EXTERIOR AND PRESS lRMLY TO ADHERE IT TO THE WATER RESISTIVE BARRIERꢇ  
£ꢂ  
'ꢇ Apply sill flashing tape #2. Cut a piece of flashing tape 12" longer  
THAN THE OPENING WIDTHꢇ !PPLY AT THE BOTTOMꢍ OVERLAPPING TAPE ꢋꢂ  
BY AT LEAST ꢂꢅꢇ $/ ./4 ALLOW THE TAPE TO EXTEND PAST THE INTERIOR  
FACE OF THE FRAMING ꢁꢂ' ꢇ  
ꢃꢇ  
£ꢄ  
In-swing doors: )F THE WALL DEPTH IS GREATER THAN ꢊꢅꢍ ADD A THIRD  
piece of flashing tape. The flashing tape should come to within 1"  
of the interior face of the framing.  
Note: The flashing tape may not fully cover the framing  
members. When using the optional fin at the bottom of the door,  
do not install the aluminum sill support or wood blocking until  
after the doors have been installed in the rough opening.  
(ꢇ Attach the aluminum sill support or wood blocking to the  
EXTERIOR OF THE BOX PLATE TO SUPPORT THE EDGE OF THE DOOR SILLꢇ  
Place the sill support flush with the subfloor.  
£ꢅ  
SETTING AND FASTENING THE DOOR  
2
A. Remove plastic wrap and cardboard packaging from door. DO  
NOT remove plastic shipping spacers. The shipping spacers will help  
keep the door square during installation. DO NOT unlock or open the  
door until it is fully fastened.  
Ó
Note: If screens, grilles or hardware are removed from the door at  
this time, label them and store them in a protected area.  
B. Fold out installation fin to 90°. Be careful not to remove or tear the  
lN CORNERSꢇ  
Note: If the fin is not at 90°, the door will not line up correctly on  
the interior. If using the optional fin at the sill, apply the fin and fin  
corners, then proceed to Step D. Sealant lines from Step C are not  
required when using the optional fin at the sill.  
Óꢀ  
C. Place three 3/8" beads of sealant. 4HE lRST BEAD SHOULD BE  
APPROXIMATELY ꢉꢀꢆꢅ FROM THE EXTERIOR OF THE ROUGH OPENINGꢍ THE SECOND  
bead should be placed so it is under the wood interior threshold of the  
door. Placement will vary depending on wall thickness and door  
type. Place a third bead of sealant in the groove of the sill support  
OR ꢂꢀꢆꢅ FROM THE EXTERIOR EDGE OF THE WOOD BLOCKINGꢇ  
Óꢁ  
&YUFSJPS  
TWO OR MORE PEOPLE WILL BE REQUIRED FOR THE  
FOLLOWING STEPS.  
D. Insert the door from the exterior of the building.  
DO NOT slide the bottom of the door into the opening. Sliding  
will damage the sealant lines. Place the bottom of the door at the  
bottom of the opening, then tilt the top into position. Center  
the door between the sides of the opening to allow clearance for  
SHIMMINGꢍ AND INSERT ONE ROOlNG NAIL IN THE lRST HOLE FROM THE  
CORNER ON EACH END OF THE TOP NAILING lNꢇ 4HESE ARE USED TO HOLD  
the door in place while shimming it plumb and square.  
 
E. Plumb and square door. Place shims at each hinge and lock  
strike location between the door and the sides of the opening.  
)NSERT SHIMS IN OTHER LOCATIONS AS NEEDED STARTING UP ꢈꢅ FROM THE  
bottom of the door to square it in the opening. Make sure that the  
REVEAL AROUND THE DOORꢁS IS EQUALꢇ /N DOUBLE DOORSꢍ MAKE SURE THAT  
panels are even across the bottom.  
Óꢃ  
&YUFSJPS  
Note: On center latch double doors the lock strike will not be  
shimmed since it is located in the center of the unit. DO NOT  
over shim.  
F. Check the interior reveal. Make sure the  
Óꢂ  
measurement from the interior face of the door  
to the interior face of the wall is equal at several  
points around the door.  
£
ꢆ ꢀꢅꢃ-  
““  
Ó
ä
Ó
Î
Î
ä
{
ä
x
ä
È
ä
Ç
ä
*OUFSJPS  
Note: If the dimensions are not equal, check  
to make sure the fins are folded out to 90° at  
all points.  
Óꢃ  
'ꢇ &ASTEN THE DOOR TO OPENING BY DRIVING ꢃꢅ GALVANIZED ROOlNG  
NAILS INTO EACH PREꢎPUNCHED HOLE IN THE NAILING lNꢇ  
Óꢃ  
Note: Make sure the fin corner is lying as flat as possible.  
When using the optional fin at the sill, attach  
the aluminum sill support or wood blocking  
under the sill of the door before proceeding  
to Step H.  
Óꢃ  
&YUFSJPS  
(ꢇ #AREFULLY OPEN THE DOORꢁS AND REMOVE ALL  
Óꢄ  
shipping spacers.  
Note: Be sure to remove the spacers from  
the bottom edge of the door panel.  
Double doors with center latch: Designer Series Only: Use the  
construction handle to operate the active door panel. Operate the  
flushbolts per the instructions on the label on the strike located on  
the astragal.  
Óꢆ  
Architect Series Only: Use the construction handle to operate both  
the active and passive door panels.  
I. Out-swing doors: Place a dab of sealant in each of the pre-  
DRILLED HOLES IN THE BOTTOM OF THE DOOR FRAMEꢍ THEN INSERT A ꢋꢌ X  
ꢃꢅ STAINLESS STEEL SCREW ꢁPROVIDED INTO EACH HOLEꢇ  
*OUFSJPS  
Óꢇ  
Note: Single doors will have two pre-drilled holes, double  
doors will have four.  
I1. Out-swing double doors only: Place a dab of sealant into the  
center hole of the strike plate located at the sill of the door.  
Óꢈ  
)NSTALL A ꢋꢌ X ꢃꢅ mAT HEAD STAINLESS STEEL WOOD SCREW ꢁPROVIDED  
into this hole.  
Note: For masonry floors, use a #8 masonry screw instead of  
the wood screw.  
J. On center latching (double) doors: Place shims at the top of the door frame above the center  
STRIKE PLATEꢇ 3ECURE THE SHIMS BY INSERTING A ꢋꢌ X ꢉꢅ mAT HEAD STAINLESS STEEL SCREW INTO THE UPPER  
door frame through the center hole of the strike plate and the shims into the rough opening.  
J1. On center hinged double doors: Insert and attach shims directly above the astragal in the center of  
the unit.  
+ꢇ /N EACH HINGEꢍ STARTING AT THE TOPꢍ INSERT A ꢉꢅ LONG SCREW ꢁPROVIDED INTO THE OPEN SCREW HOLEꢇ Make  
sure that the screw passes through the shims and into the structural framing.  
Note: This step does not apply to center hinge double doors.  
 
L. Check door operation. Open and close the door to check for proper operation. Make  
sure the door will latch correctly.  
Note: If there are any problems with the operation, recheck and  
adjust the reveal.  
M. Adjust the reveal if needed. The door panels have adjustable hinge  
LEAFSꢇ 5SING A ꢂꢀꢌꢅ ALLEN WRENCH TURN THE CENTER SCREW CLOCKWISE TO  
increase the space between the hinge side of the frame and the door  
panel, or counter clockwise to increase the space between the door  
panel and the lock side of the frame. DO NOT turn the screws more  
than a 3/4 turn in either direction. In some cases it may be necessary  
to loosen and then tighten the top and bottom hinge screws to obtain  
full hinge adjustment. If necessary, loosen the top and bottom screws,  
and immediately retighten them. With the screws retightened, turn the  
adjustment hinge screw. If the hinge will not adjust any further then  
it is adjusted as far as it will go. If more clearance is needed adjust the  
shims between the frame and the rough opening.  
Óꢊ  
Ó  
Note: DO NOT adjust the hinge with the top and bottom screws  
loose; this could force the hinge to adjust beyond its design capability  
which can cause the hinge to bind, damage the hinge and/or pull out  
the screws. A 3/4 turn of the center screw provides approximately  
1/16" adjustment.  
N. On doors with a lock strike in the side, DRILL A ꢂꢀꢌꢅ DIAMETER X ꢃꢅ DEEP  
PILOT HOLE THROUGH THE LOCK STRIKE AND INTO THE ROUGH OPENINGꢇ )NSERT A ꢋꢌ X  
ꢉꢅ SCREW ꢁPROVIDED INTO THE PILOT HOLE MAKING SURE THAT IT PASSES THROUGH THE  
shim and into the stud.  
Note: This step does not apply to center latching double doors.  
O. Install a #8 x 3" flat head stainless steel screw INTO THE HOLE LOCATED APPROXIMATELY  
ꢌꢅ FROM THE TOP OF THE DOOR FRAMEꢍ ON THE LATCH SIDE OF THE FRAMEꢇ  
INTEGRATING THE DOOR TO  
THE WATER RESISTIVE BARRIER  
3
Note: The flashing tape must be applied approximately 1/2"  
onto the frame cladding at the jambs and head. Pre-folding the  
tape at 1/2" before removing the paper backing will make it  
easier to apply the tape correctly. If the siding is less than 1/2"  
thick, adjust the dimension of the fold so the exterior sealant  
line will cover the exterior edge of the tape.  
A. Apply side flashing tape. Cut two  
pieces of flashing tape 4" longer than  
the frame height of the door. Apply one  
piece 1/2" onto the frame cladding,  
OVER THE NAILING lN AND ONTO THE WATER  
resistive barrier on each side. The tape  
SHOULD EXTEND ꢃꢅ ABOVE THE TOP OF THE  
door and 2" below the bottom of the  
DOORꢇ 0RESS THE TAPE DOWN lRMLY WHILE  
FOLDING DOWN THE EXCESS TAPE AT THE TOP  
and bottom of the door.  
&YUFSJPS  
Îꢉ  
 
B. Apply top flashing tape. Cut a piece of flashing tape long  
ENOUGH TO GO ACROSS THE TOP OF THE DOOR AND EXTEND AT  
least 1" past the side flashing tape on both sides. Apply  
the tape 1/2" onto the frame cladding, over the top  
NAILING lN AS SHOWNꢇ &OLD THE OVERLAPPING TAPE DOWNꢍ  
AND PRESS ALL TAPE DOWN lRMLYꢇ  
Note: The top flashing tape must overlap the  
side flashing tape to prevent water from getting  
behind it.  
Î
ꢃꢇ  
C. Fold down top flap OF WATER RESISTIVE BARRIER ꢁꢉ# ꢇ  
Îꢀ  
&YUFSJPS  
D. Apply flashing tape to diagonal cuts. Cut pieces of  
flashing tape at least 1" longer than the diagonal cuts  
in the water resistive barrier. Apply the tape covering  
the entire diagonal cut in the water resistive barrier  
at both upper corners of the door.  
Note: Be sure to overlap the top corners (3D).  
Îꢁ  
INTERIOR SEAL  
Caution: Ensure use of low pressure polyurethane window and door insulating foams and strictly  
follow the foam manufacturer’s recommendations for application. Use of high pressure foams or  
improper application of the foam may cause the door frame to bow and hinder operation.  
4
A. Apply insulating foam sealant. From the interior,  
INSERT THE NOZZLE OF THE APPLICATOR APPROXIMATELY ꢂꢅ  
deep into the space between the door and the rough  
*OUFSJPS  
opening and apply a 1" deep bead of foam. This  
WILL ALLOW ROOM FOR EXPANSION OF THE FOAM AND WILL  
MINIMIZE SQUEEZE OUTꢇ )F USING FOAM OTHER THAN 'REAT  
Stuff Window and Door Insulating Foam Sealant by  
the Dow Chemical Company, allow the foam to cure  
{ꢉ  
COMPLETELY ꢁUSUALLY ꢌ TO ꢃꢆ HOURS BEFORE PROCEEDING  
TO THE NEXT STEPꢇ  
Note: DO NOT completely fill the space from the  
back of the fin to the interior face of the opening.  
B. Check the door operation by opening and closing the door.  
Note: If the door does not operate correctly, check to make sure it is still plumb, level,  
square and that the sides are not bowed. If adjustments are required, remove the foam  
with a serrated knife. Adjust the shims, and reapply the insulating foam sealant.  
 
SEALING THE DOOR TO THE EXTERIOR WALL CLADDING  
When applying siding, brick veneer or other exterior finish material, leave adequate space between  
the door frame and the material for sealant. Refer to the illustration that corresponds to your  
finish material.  
5
Note: The sealant details shown are standard recommendations from the sealant industry. Contact  
your sealant supplier for recommendations and instructions for these and any other applications.  
#3*$,ꢀ7&/&&3  
7*/:-ꢋ45&&-  
4*%*/(  
#BDLFSꢀ3PEꢀBOE  
4FBMBOUꢀUZQJDBM  
#BDLFSꢀ3PEꢀBOE  
4FBMBOUꢀUZQJDBM  
ꢃꢋꢂꢇꢀ$MFBSBODF  
ꢃꢋꢂꢇꢀ$MFBSBODF  
"DDFTTPSZꢀ(SPPWF  
"DDFTTPSZꢀ(SPPWF  
*OTVMBUJOH  
'PBN  
*OTVMBUJOH  
'PBN  
1FSJNFUFSꢀ4FBMBOUꢀ  
NVTUꢀFYUFOEꢀUPꢀ  
SPPNꢀTJEFꢀPGꢀ  
1FSJNFUFSꢀ4FBMBOUꢀ  
NVTUꢀFYUFOEꢀUPꢀ  
SPPNꢀTJEFꢀPGꢀ  
"DDFTTPSZꢀ(SPPWFꢉ  
"DDFTTPSZꢀ(SPPWFꢉ  
ꢃꢋꢂꢇ  
ꢃꢋꢂꢇ  
800%ꢀ4*%*/(  
8*5)ꢀ53*.  
800%  
4*%*/(  
ꢊꢋꢌꢇ  
.JOꢉ  
ꢊꢋꢌꢇ  
.JOꢉ  
4FBMBOUꢀUZQJDBM  
4FBMBOUꢀUZQJDBM  
ꢃꢋꢂꢇꢀ$MFBSBODF  
ꢃꢋꢌꢇꢀ$MFBSBODF  
"DDFTTPSZ  
(SPPWF  
"DDFTTPSZꢀ(SPPWF  
*OTVMBUJOH  
'PBN  
*OTVMBUJOH  
'PBN  
1FSJNFUFSꢀ4FBMBOUꢀ  
NVTUꢀFYUFOEꢀUPꢀ  
SPPNꢀTJEFꢀPGꢀ  
"DDFTTPSZꢀ(SPPWFꢉ  
ꢃꢋꢌꢇ  
ꢃꢋꢂꢇ  
ꢊꢋꢌꢇ  
.JOꢉ  
A. Install the hardware. Refer to the instructions  
INCLUDED IN THE HARDWARE BOXꢇ  
B. Insert closed cell foam backer rod into the space  
AROUND THE DOOR SO THERE IS APPROXIMATELY ꢉꢀꢌꢅ TO ꢂꢀꢃꢅ  
CLEARANCE BETWEEN THE BACKER ROD AND THE EXTERIOR FACE  
of the door.  
Note: Backer rod adds shape and depth for the  
sealant line.  
x
C. Apply a bead of high quality exterior grade sealant  
to the entire perimeter of the door. At each end of  
the bottom of the door, insert sealant into the spaces  
between the bottom of door and the sill support and  
connect it to the perimeter sealant.  
xꢀ  
D. Shape, tool and clean excess sealant. 7HEN lNISHEDꢍ  
the sealant should be the shape of an hourglass.  
Note: This method creates a more flexible sealant  
line capable of expanding and contracting.  
E. Remove plastic guards at the base of the door  
once construction is complete.  
 
INTERIOR FINISHING  
)F PRODUCTS CANNOT BE lNISHED IMMEDIATELYꢍ COVER WITH CLEAR PLASTIC TO PROTECT FROM DIRTꢍ DAMAGE AND  
MOISTUREꢇ 2EMOVE ANY CONSTRUCTION RESIDUE BEFORE lNISHINGꢇ 3AND ALL WOOD SURFACES LIGHTLY WITH ꢂꢌꢄ  
GRIT OR lNER SANDPAPERꢇ $/ ./4 USE STEEL WOOLꢇ "% #!2%&5, ./4 4/ 3#2!4#( 4(% ',!33ꢇ  
Remove sanding dust.  
0ELLA PRODUCTS MUST BE lNISHED PER THE BELOW INSTRUCTIONSꢏ FAILURE TO FOLLOW THESE INSTRUCTIONS VOIDS THE  
Limited Warranty.  
s /N CASEMENT AND AWNINGSꢍ IT IS OPTIONAL TO PAINTꢍ STAIN OR lNISH THE VERTICAL AND HORIZONTAL SASH EDGESꢇ  
s /N SINGLEꢎHUNG AND DOUBLEꢎHUNGꢍ DO NOT PAINTꢍ STAIN OR lNISH THE VERTICAL SASH EDGESꢍ ANY lNISH ON  
THE VERTICAL SASH EDGES MAY CAUSE THE SASH TO STICKꢏ IT IS OPTIONAL TO PAINTꢍ STAIN OR lNISH THE HORIZONTAL  
sash edges.  
s /N PATIO DOORSꢍ IT IS OPTIONAL TO PAINTꢍ STAIN OR lNISH THE VERTICAL AND HORIZONTAL PANEL EDGESꢇ  
Note: To maintain proper product performance do not paint, finish or remove the weather-  
stripping, mohair dust pads, gaskets or vinyl parts. Air and water leakage will result if these parts  
are removed. After finishing, allow venting windows and doors to dry completely before closing  
them.  
0ELLA #ORPORATION IS NOT RESPONSIBLE FOR INTERIOR PAINT AND STAIN lNISH IMPERFECTIONS FOR ANY PRODUCT  
THAT IS NOT FACTORYꢎAPPLIED BY 0ELLA #ORPORATIONꢇ 5SE OF INAPPROPRIATE lNISHESꢍ SOLVENTSꢍ BRICKWASHꢍ OR  
cleaning chemicals will cause adverse reactions with window and door materials, and voids the Limited  
Warranty.  
&OR ADDITIONAL INFORMATION ON lNISHING SEE THE 0ELLA /WNERgS -ANUAL OR GOT TO www.pella.com.  
EXTERIOR FINISH  
4HE EXTERIOR FRAME AND SASH ARE PROTECTED BY ALUMINUM CLADDING WITH OUR TOUGH %NDURA#LAD® or  
%NDURA#LAD 0LUS BAKEDꢎON FACTORY lNISH THAT NEEDS NO PAINTINGꢇ #LEAN THIS SURFACE WITH MILD SOAP  
and water. Stubborn stains and deposits may be removed with mineral spirits. DO NOT use abrasives.  
DO NOT scrape or use tools that might damage the surface.  
5SE OF INAPPROPRIATE lNISHESꢍ SOLVENTSꢍ BRICKWASH OR CLEANING CHEMICALS WILL CAUSE ADVERSE REACTIONS  
with window and door materials and voids the Limited Warranty.  
CARE AND MAINTENANCE  
Care and maintenance information is available in the Pella Owner’s Manual. You can obtain an owner’s  
manual by contacting your local Pella retailer. This information is also available on www.pella.com.  
IMPORTANT NOTICE  
"ECAUSE ALL CONSTRUCTION MUST ANTICIPATE SOME WATER INlLTRATIONꢍ IT IS IMPORTANT THAT THE WALL SYSTEM BE  
designed and constructed to properly manage moisture. Pella Corporation is not responsible for claims  
OR DAMAGES CAUSED BY ANTICIPATED AND UNANTICIPATED WATER INlLTRATIONꢏ DElCIENCIES IN BUILDING DESIGNꢍ  
CONSTRUCTION AND MAINTENANCEꢏ FAILURE TO INSTALL 0ELLA PRODUCTS IN ACCORDANCE WITH 0ELLAꢐS INSTALLATION  
INSTRUCTIONSꢏ OR THE USE OF 0ELLA PRODUCTS IN WALL SYSTEMS WHICH DO NOT ALLOW FOR PROPER MANAGEMENT  
of moisture within the wall systems. The determination of the suitability of all building components,  
including the use of Pella products, as well as the design and installation of flashing and sealing systems  
are the responsibility of the Buyer or User, the architect, contractor, installer, or other construction  
professional and are not the responsibility of Pella.  
Pella products should not be used in barrier wall systems which do not allow for proper management of  
MOISTURE WITHIN THE WALL SYSTEMSꢍ SUCH AS BARRIER %XTERIOR )NSULATION AND &INISH 3YSTEMSꢍ ꢁ%)&3 ꢁALSO  
KNOWN AS SYNTHETIC STUCCO OR OTHER NONꢎWATER MANAGED SYSTEMSꢇ %XCEPT IN THE STATES OF #ALIFORNIAꢍ  
.EW -EXICOꢍ !RIZONAꢍ .EVADAꢍ 5TAHꢍ AND #OLORADOꢍ Pella makes no warranty of any kind on and  
assumes no responsibility for Pella windows and doors installed in barrier wall systems. In the  
states listed above, the installation of Pella products in barrier wall or similar systems must be in  
accordance with Pella’s installation instructions.  
0RODUCT MODIlCATIONS THAT ARE NOT APPROVED BY 0ELLA #ORPORATION WILL VOID THE ,IMITED 7ARRANTYꢇ  
 

Pelco Camera Accessories ICS210 CM User Manual
Philips Car Stereo System CEM3000B User Manual
Philips Computer Monitor 107T73 User Manual
Philips Cordless Telephone TU7372 User Manual
Philips CRT Television 15PT2527 User Manual
Philips Speaker AS351 User Manual
Philips Styling Iron HP4661 User Manual
Premium Home Creations Swimming Pool K 2369 User Manual
ProForm Treadmill PFTL700100 User Manual
PYLE Audio Speaker PDW18125 User Manual